切换到宽版
  • 广告投放
  • 稿件投递
  • 繁體中文
    • 4193阅读
    • 8回复

    [求助]codev约束操作问题 [复制链接]

    上一主题 下一主题
    离线yinge丶
     
    发帖
    355
    光币
    27
    光券
    0
    只看楼主 倒序阅读 楼主  发表于: 2017-06-16
    — 本帖被 cyqdesign 从 光电产业资讯及信息发布 移动到本区(2017-06-16) —
    codev的一般约束是不是很难控制厚度,稍微一优化就会出现负数 ~G 3txd  
    ,或者是说必须加入特定约束来控制吗
     
    分享到
    离线yinge丶
    发帖
    355
    光币
    27
    光券
    0
    只看该作者 1楼 发表于: 2017-06-16
    @Cyqdesign,好像发错版块了
    本帖提到的人: @cyqdesign
    离线cyqdesign
    发帖
    28038
    光币
    91526
    光券
    0
    只看该作者 2楼 发表于: 2017-06-16
    回 yinge丶 的帖子
    yinge丶:@Cyqdesign,好像发错版块了 (2017-06-16 10:50)  =~hb&  
    (O4oI U  
    已经转移。
    本帖提到的人: @cyqdesign
    光行天下网站、公众号广告投放、企业宣传稿件发布,请联系QQ:9652202,微信号:cyqdesign
    离线amanda279
    发帖
    145
    光币
    86
    光券
    0
    只看该作者 3楼 发表于: 2017-06-20
    个人感觉codeV 控制厚度还是可以的吧
    离线帮助
    发帖
    107
    光币
    10
    光券
    0
    只看该作者 4楼 发表于: 2017-06-25
    我觉得很容易啊,一般不会出错的
    离线466047861
    发帖
    188
    光币
    1736
    光券
    2
    只看该作者 5楼 发表于: 2017-07-25
    除了在一般约束那控制外,特殊约束也要对中心厚度和边缘厚度的控制,这样就很少出现负数的了
    离线yinge丶
    发帖
    355
    光币
    27
    光券
    0
    只看该作者 6楼 发表于: 2017-07-28
    翻阅了手册,觉得下面的解答比较合适: f=l/Fp}4UH  
    On any given surface there can be only one active general thickness constraint. If on a given surface more than one of the general thickness constraints is in violation, AUTO selects the one with the largest violation and controls it for that cycle (it may release it and control a different one on the next cycle). In a zoomed system this same technique is used, although it may not be sufficient in all cases. In a “true zoom” system, this technique is sufficient to control all the general thickness constraints. However, in a general zoom system, or multi-configuration system, this technique may not be sufficient and it may be necessary for you to enter specific CT and/or ET constraints as a function of zoom position (remember that entering either CT or ET specific constraints in any zoom position disables all the general thickness constraints for all zoom positions on that surface). <!sLf z?  
    离线yinge丶
    发帖
    355
    光币
    27
    光券
    0
    只看该作者 7楼 发表于: 2017-07-28
    回 466047861 的帖子
    466047861:除了在一般约束那控制外,特殊约束也要对中心厚度和边缘厚度的控制,这样就很少出现负数的了 (2017-07-25 07:18)  %M iv8  
    ]CzK{-W  
    是这样子的
    离线枫之枯
    发帖
    248
    光币
    44
    光券
    0
    只看该作者 8楼 发表于: 2020-05-21
    谢谢分享