各位高手，请教一下，新手学zemax编程，照着敲了一段程序，在zemax中ZPL程序为什么运行不了，还请各位高手指点指点，谢谢！ :CNHN2 J
?PO~$dUc]
l(-6pP5`
6HW<E~G'6
h1^q};3!W\
?a+t L'D[
XI~2Vzht
sZ /~pk
Em N0K'x
}H&NR?Ax
Eb7qM.Q] &
#DXC 6f
" 6Hka{
TyY[8J|
ZPL程序代码如下： > nDx)!I
U
N 1HBW ;
! ex30401 bJj <xjBM
! This program shows how to create a doublet from scratch 2$.
u bA
z _~ 5c
! set system parameters .cdm@_Ls
SYSP 30, 0 # set lens unit as mm oe}nrkmb
[cv7s=U%
SYSP 10, 0 # set system aperture as Entrance Pupil Diameter 7hqa|
SYSP 11, 50 # set system aperture value as 50mm rhO
]4A
.Wv2aJq
SYSP 201, 3 # set total wavelength number as 3 vz</|s
SYSP 202, 1, 0.48613270 # set the 1st wavelength as 0.48613270 micron L1D{LzlBti
SYSP 202, 2, 0.58756180 # set the 2nd wavelength as 0.58756180 micron -9Wx;u4]o
SYSP 202, 3, 0.65627250 # set the 3rd wavelength as 0.65627250 micron O,>1GKw"\
SYSP 203, 1, 1 # set the 1st wavelength weight as 1 I2hX; pk,
SYSP 203, 2, 1 # set the 2nd wavelength weight as 1 (Hb
i+IHV
SYSP 203, 3, 1 # set the 3rd wavelength weight as 1 j(F&*aH78
= W"BfG
SYSP 200, 2 # set the 2nd wavelength as the primary wavelength axW3#3#`
TBHIcX
SYSP 100, 0 # set the field type as angle ??5qR8n.
SYSP 101, 3 # set the total field number as 3 55 )!cw4
SYSP 102, 1, 0 # set field 1 as x=0 degree >Ip>x!wi
SYSP 103, 1, 0 # set field 1 as y=0 degree P dcF
SYSP 104, 1, 1 # set field 1 as weight=1 qRT1W re
3
SYSP 102, 2, 0 # set field 2 as x=0 degree :[ z=u
SYSP 103, 2, 3.5 # set field 2 as y=3.5 degree H)(@A W+-
SYSP 104, 2, 1 # set field 2 as weight=1 *Nloa/a&9
SYSP 102, 3, 0 # set field 3 as x=0 degree NWd% Za5K;
SYSP 103, 3, 5 # set field 3 as y=5 degree h~ )oiT2v
SYSP 104, 3, 1 # set field 3 as weight=1 NTS
tk{s,
Wu(6FQ`H
! set surface 1 as stop SV}q8z\
STOPSURF 1 s7e)M t
o65:)z
u
! insert 3 surfcaces after stop -e_ IDE
INSERT 2 uUu]JDdz
INSERT 2
s. &ewf\
INSERT 2 Z [<rz6%cB
jE|Ju:}&
! set surface parameters R
h zf.kp
SURP 1, THIC, 275 # set surface 1 thickness as 275 !7 "-9n
H6X]D"Y,
SURP 2, TYPE, "STANDARD" # set surface 2 type as "STANDARD",can be omitted ]S4 TX
SURP 2, COMM, "front f1" # set surface 2 comment 0 Po", \^
SURP 2, CURV, 1/600 # set surface 2 curvature as 1/600 KSU?Tg&JR
SURP 2, THIC, 18 # set surface 2 thickness as 18 ]CsF} wr'z
SURP 2, GLAS, "BK7" # set surface 2 glass type as BK7 WW82=2rJ9
Rs,\{#
SURP 3, COMM, "back f1/front f2" # set surface 3 comment v*`$is+
SURP 3, CURV, -1/115 # set surface 3 curvature as -1/115 k_?xi OSh
SURP 3, THIC, 18 # set surface 3 thickness as 18 hn\<'|n
SURP 3, GLAS, "F2" # set surface 3 glass type as F2 (yIl ]ZN*
sJo]$/?F
SURP 4, COMM, "back f2" # set surface 4 comment 4^vEMq 8lB
SURP 4, CURV, -1/243 # set surface 4 curvature as -1/243 (oO*|\9u
SURP 4, THIC, 395 # set surface 4 thickness as 395 ]v j=M-:+
H'|b$rP0@
UPDATE
