各位高手，请教一下，新手学zemax编程，照着敲了一段
程序，在zemax中ZPL程序为什么运行不了，还请各位高手指点指点，谢谢！
)`mBvS.} v]}\Ns/ 
}-T,cA_H| l] ~IZTC 
zu
7Fq ]zD a.a
,_ 
D J7U6{KLq T`GiM%R;g 
bKE iS8x gSe3S-Lt 
*n6L3"cO /-+ hMYe 
I ^[[*Bh*C 7"OJ,Mx% ZPL程序代码如下：
v[)8 1uY be Ny5~M$ ! ex30401
Tl1H2s=G- ! This program shows how to create a doublet from scratch
vx}BT H Ko|gH]B' ! set system parameters
QZuKM 'D+ SYSP 30, 0 # set lens unit as mm
$weC '-n@ aj<r= SYSP 10, 0 # set system aperture as Entrance Pupil Diameter
^z51f>C SYSP 11, 50 # set system aperture value as 50mm
p =-~qBw w: mm@8N SYSP 201, 3 # set total wavelength number as 3
F^5\w-gLY SYSP 202, 1, 0.48613270 # set the 1st wavelength as 0.48613270 micron
hoLA *v2< SYSP 202, 2, 0.58756180 # set the 2nd wavelength as 0.58756180 micron
)_6W@s SYSP 202, 3, 0.65627250 # set the 3rd wavelength as 0.65627250 micron
[GcW *v SYSP 203, 1, 1 # set the 1st wavelength weight as 1
R \]C;@J< SYSP 203, 2, 1 # set the 2nd wavelength weight as 1
DVDzYR**4 SYSP 203, 3, 1 # set the 3rd wavelength weight as 1
|7${E^u x ~K79Mya SYSP 200, 2 # set the 2nd wavelength as the primary wavelength
o'8nQ
Tao 7xfS%'=y" SYSP 100, 0 # set the field type as angle
/QQjb4 S} SYSP 101, 3 # set the total field number as 3
YPA$38 SYSP 102, 1, 0 # set field 1 as x=0 degree
#$F*.vQSs+ SYSP 103, 1, 0 # set field 1 as y=0 degree
I1I -,~hO SYSP 104, 1, 1 # set field 1 as weight=1
&y7xL-xP SYSP 102, 2, 0 # set field 2 as x=0 degree
0E)M6
jJ SYSP 103, 2, 3.5 # set field 2 as y=3.5 degree
A2 $05a$% SYSP 104, 2, 1 # set field 2 as weight=1
!OMCsUZ SYSP 102, 3, 0 # set field 3 as x=0 degree
hE<Sm*HU SYSP 103, 3, 5 # set field 3 as y=5 degree
E()%IC/R SYSP 104, 3, 1 # set field 3 as weight=1
mA@!t>=oMq E'NS$ ,h ! set surface 1 as stop
B:Awy/XMi STOPSURF 1
P'DcNMdw wuM'M<J@ ! insert 3 surfcaces after stop
_]{LjJ!M INSERT 2
/y6I I$AvM INSERT 2
X z9[0;Q INSERT 2
&9"Y:), :Gew8G ! set surface parameters
>]o>iOz;] SURP 1, THIC, 275 # set surface 1 thickness as 275
wuW{ 2+)B [ako8 SURP 2, TYPE, "STANDARD" # set surface 2 type as "STANDARD",can be omitted
d24_,o\_ SURP 2, COMM, "front f1" # set surface 2 comment
iio-RT?! SURP 2, CURV, 1/600 # set surface 2 curvature as 1/600
?7J ::}R SURP 2, THIC, 18 # set surface 2 thickness as 18
qw>v u7/z SURP 2, GLAS, "BK7" # set surface 2 glass type as BK7
$\|Q+ 7lQ 4C ;y2`C SURP 3, COMM, "back f1/front f2" # set surface 3 comment
2+Oz$9`. SURP 3, CURV, -1/115 # set surface 3 curvature as -1/115
lxr;AJ( SURP 3, THIC, 18 # set surface 3 thickness as 18
L27WD m^) SURP 3, GLAS, "F2" # set surface 3 glass type as F2
b=U3&CV9 6 N:Ps8Hg SURP 4, COMM, "back f2" # set surface 4 comment
USS%T<Vk SURP 4, CURV, -1/243 # set surface 4 curvature as -1/243
hljKBx ~ SURP 4, THIC, 395 # set surface 4 thickness as 395
7_jlNr7uk :,g]Om^ UPDATE
