引用第0楼toshiba于2006-12-12 14:12发表的 计算机辅助设计—Pro ENGINEER Wildfire实用教程 : -<@QR8:
上个不好,错了. Qg
gx:
改正后再传 f/%QMhM:
有PRO/E30 F000破解方法的仁兄帮帮发给小弟一个
mI3
\n 破解說明:
)\l(h%s[I 1.start pro/e setup
5VK.Zs\ 開始安裝
]"-c?%L f]]UNS$AYQ OVU+V 0w1a 2.open ptc_licfile.dat with your fav txt-editor
(b;*8 使用你最常用的文字編輯器 打開ptc_licfile.dat
|Fp+9U tF~D!t@ nY 50dFA, 3.replace every occurance of <HOSTID> with the one shown in the bottom left corner of the Pro/e setup
ffoLCx4o0E (its your mac-id, format: xx-xx-xx-xx-xx)
pJ3Yjm[l 把你的 網路卡序號打在每一個 <HOSTID>位。(可使用搜尋及取代功能)
"DU1k6XC rCgoU
xW` 例如:HOSTID=PTC_HOSTID=<HOSTID>
(2p<I)t 改成:HOSTID=PTC_HOSTID=00-13-CE-4C-21-79
/nVGr]t_pj b&E9xD/;r u%I |o s] 4.安裝PROE
>sm<$'vZ/ ^*_|26 .install pro/e - pro/m - pro/ds, i dont care which one or in which order
I&|J +B?# .on license-config screen select "nodelocked license" and point to edited ptc_licfile.dat
;]sbz4? .blalala install
YuKg|<WO kr>H,%3~ C`r{B.t`GT 5.next for pro/engineer:(以下為針對pro/engineer模組之破解)
Y>Tok|PV a) (if u didnt install the complete package, u get "missing file" errors, accept or bleed)
yZw5?{g@ (如果有些模組沒安裝, 破解時會出現檔案找不到訊息)
;FO( mL ( *^Xtorqo b) run ptc.pro engineer.wildfire.3.0.m060-patch.exe, point to <installdir>\i486_nt\obj folder
PQA}_o 將SHooTERS\ptc.pro engineer.wildfire.3.0.m060-patch.exe複製到<安裝路徑>\i486_nt\obj下並執行。
Uy5G,! .p$tb2%r c) edit <pro/e installdir>\bin\proev.bat
#f-pkeaeq 以文字編輯器編輯<pro/e安裝路徑>\bin\proev.bat
5!*@gn w-wap e) change "%start_cmd% "%CGTECH_JRE%\bin\javaw" -Xms16m -Xmx64m -Xss4m -classpath "%CGTECH_CLASSES%;%CGTECH_CLASSES%\CGTech.jar" Vericut %argstr%" in
^M~Z_CQL2 "%start_cmd% "%CGTECH_JRE%\bin\javaw" -Xms16m -Xmx64m -Xss4m -classpath "%CGTECH_CLASSES%;%CGTECH_CLASSES%\CGTech.jar" Vericut %argstr% PTC_KEY=0"
G"D=ozr (add PTC_KEY=0)
F0]xc 將第2行" "內的字串複製起來,將<pro/e安裝路徑>\bin\proev.bat內如第1行" "內的字串替換。
{?hpW+1,# 8c^Hfjr0 x#c%+ 6.pro/mechanica:(以下為針對pro/mechanica模組之破解)
> xie+ ^ .point to <pro/m installdir>\i486_nt\bin
b>x03% <pro/m installdir>\i486_nt\obj
^g
N/ 5 <pro/m installdir>\i486_nt\ptc
`|WEzW~ 將SHooTERS\ptc.pro mechanica.wildfire.3.0.m060-patch.exe複製到<安裝路徑>\i486_nt\obj並執行
@e:=
D <安裝路徑>\i486_nt\ptc並執行
<tto8Y
j 20?@t.aMp ,4H/>yPw 7.pro/distributed services:(以下為針對pro/distributed services模組之破解)
#bwGDF .run ptc.distributed.services.m060-patch.exe and point to <pro/ds installdir>\i486_nt\obj
P87Lo4Rd E(g$f.9 將SHooTERS\ptc.distributed.services.m060-patch.exe複製到<安裝路徑>\i486_nt\obj並執行
7Xf52\7n IaT\ymm` Ld?'X=eQ 重要:6、7項為針對有安裝此模組時,才需要作此部份之破,否則只需破解pro/engineer模組即可。
XJe}^k PnZC
I!Mw 8.大功告成。