引用第0楼toshiba于2006-12-12 14:12发表的 计算机辅助设计—Pro ENGINEER Wildfire实用教程 : ]
D6|o5
上个不好，错了． {g_@Tuu
改正后再传 c3W
BALdh
有ＰＲＯ／Ｅ３０ Ｆ０００破解方法的仁兄帮帮发给小弟一个
OD|1c6+X
破解說明: N,|r1u 9X#
1.start pro/e setup ~K` 1
開始安裝 hy!6g n
F.
T@)7
j|(:I: ]
2.open ptc_licfile.dat with your fav txt-editor jyQ VSQ s
使用你最常用的文字編輯器 打開ptc_licfile.dat J3IRP/*z
'HB~Dbq`V
Xm@aYNV
3.replace every occurance of <HOSTID> with the one shown in the bottom left corner of the Pro/e setup t 7^D-l
(its your mac-id, format: xx-xx-xx-xx-xx) [b;Uz|o
把你的 網路卡序號打在每一個 <HOSTID>位。(可使用搜尋及取代功能) Noz&noq
9|3o<
例如：HOSTID=PTC_HOSTID=<HOSTID> VY igxhP7
改成：HOSTID=PTC_HOSTID=00-13-CE-4C-21-79 x8/us
41}/w3Z4
/buW AX 1
4.安裝PROE 2kJ!E@n 7
<T4(H[9B
.install pro/e - pro/m - pro/ds, i dont care which one or in which order c ,$mWTC
.on license-config screen select "nodelocked license" and point to edited ptc_licfile.dat e1 uM R-Q
.blalala install c[:Wf<% |
5#!ogKQ(i
}p* ?1N
5.next for pro/engineer:(以下為針對pro/engineer模組之破解) &^+3er rO
a) (if u didnt install the complete package, u get "missing file" errors, accept or bleed) i| 4_ m
(如果有些模組沒安裝, 破解時會出現檔案找不到訊息) TPK @*9rI
|D<+X^0'
b) run ptc.pro engineer.wildfire.3.0.m060-patch.exe, point to <installdir>\i486_nt\obj folder S &01S X6
將SHooTERS\ptc.pro engineer.wildfire.3.0.m060-patch.exe複製到<安裝路徑>\i486_nt\obj下並執行。 j sZY{s=
`
FxtLG,F
c) edit <pro/e installdir>\bin\proev.bat ~p.%.b;~t
以文字編輯器編輯<pro/e安裝路徑>\bin\proev.bat 0 '@u !m?
VVLIeJ(*XT
e) change "%start_cmd% "%CGTECH_JRE%\bin\javaw" -Xms16m -Xmx64m -Xss4m -classpath "%CGTECH_CLASSES%;%CGTECH_CLASSES%\CGTech.jar" Vericut %argstr%" in v.b5iv 5
"%start_cmd% "%CGTECH_JRE%\bin\javaw" -Xms16m -Xmx64m -Xss4m -classpath "%CGTECH_CLASSES%;%CGTECH_CLASSES%\CGTech.jar" Vericut %argstr% PTC_KEY=0" <jFSj=cIL
(add PTC_KEY=0) "mt p0
將第2行" "內的字串複製起來，將<pro/e安裝路徑>\bin\proev.bat內如第1行" "內的字串替換。 D$hQyhz'
~6sE an3p
9P0yv3
6.pro/mechanica:(以下為針對pro/mechanica模組之破解) ^#w{/C/n
.point to <pro/m installdir>\i486_nt\bin G/(*foT8SE
<pro/m installdir>\i486_nt\obj QkE,T0,/?h
<pro/m installdir>\i486_nt\ptc :'Xr/| s
將SHooTERS\ptc.pro mechanica.wildfire.3.0.m060-patch.exe複製到<安裝路徑>\i486_nt\obj並執行 @'gl~J7
<安裝路徑>\i486_nt\ptc並執行 +c r
p%8 v`
!qaDn.9
7.pro/distributed services:(以下為針對pro/distributed services模組之破解) $}4K`Iu
.run ptc.distributed.services.m060-patch.exe and point to <pro/ds installdir>\i486_nt\obj `j:M)2:*y
ph#efY`a:
將SHooTERS\ptc.distributed.services.m060-patch.exe複製到<安裝路徑>\i486_nt\obj並執行 8 }z3CuM
lM+ xU;
PY -+ Bf
重要：6、7項為針對有安裝此模組時，才需要作此部份之破，否則只需破解pro/engineer模組即可。 ~},~c:fF?
+f|6AeE
8.大功告成。
|
